C OM‐05291‐01April 8, 2002Rev. G 04‐22‐13THE GORMAN‐RUPP COMPANY MANSFIELD, OHIOwww.grpumps.comGORMAN‐RUPP OF CANADA LIMITED ST. THOMAS, ONTARIO,
OM-05291SUPER T SERIESPAGE B - 3INSTALLATIONLines near the pump must be independently supported to avoid strain on the pump which couldcause excessiv
OM-05291 SUPER T SERIESPAGE B - 4 INSTALLATIONNOTEThe pipe submergence required may be reducedby installing a standard pipe increaser fitting at thee
OM-05291SUPER T SERIESPAGE B - 5INSTALLATIONDo not install a manual shut‐off valve in a bypassline. If a manual shut‐off valve is installed to facili
OM-05291 SUPER T SERIESPAGE B - 6 INSTALLATIONvalve is fully closed. Be sure the bypassline is directed back to the wet well ortank to prevent hazardo
OM-05291SUPER T SERIESPAGE B - 7INSTALLATIONment will occur in transit and handling. Pumpsmust be checked and realigned before operation.Before checki
OM-05291 SUPER T SERIESPAGE B - 8 INSTALLATIONTighten the belts in accordance with the belt manufacturer's instructions. If the belts are too lo
SUPER T SERIESOM-05291OPERATION PAGE C - 1OPERATION - SECTION CReview all SAFETY information in Section A.Follow the instructions on all tags, labels
SUPER T SERIESOM-05291OPERATIONPAGE C - 2reading on the discharge pressure gauge or by aquieter operation. The pump may not prime immediately because
SUPER T SERIESOM-05291OPERATION PAGE C - 3Open the suction line, and read the vacuum gaugewith the pump primed and at operation speed.Shut off the pum
OM-05291SUPER T SERIESTROUBLESHOOTING PAGE D - 1TROUBLESHOOTING - SECTION DReview all SAFETY information in Section A.Before attempting to open or ser
Register your newGorman‐Rupp pump online atwww.grpumps.comValid serial number and e‐mail address required.RECORD YOUR PUMP MODEL AND SERIAL NUMBERPlea
OM-05291 SUPER T SERIESTROUBLESHOOTINGPAGE D - 2TROUBLE POSSIBLE CAUSE PROBABLE REMEDYPUMP STOPS OR FAILSTO DELIVER RATEDFLOW OR PRESSURE(cont.)Suctio
OM-05291SUPER T SERIESTROUBLESHOOTING PAGE D - 3PREVENTIVE MAINTENANCESince pump applications are seldom identical, andpump wear is directly affected
OM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 1PUMP MAINTENANCE AND REPAIR - SECTION EMAINTENANCE AND REPAIR OF THE WEARING PARTS OF THE PUM
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 2SECTION DRAWINGPARTS PAGEFigure E-1. Pump Model T10A60S-B, /FM, /WW
ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTYOM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 3
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 4SECTION DRAWINGFigure E‐2. 44163-308 And 44163-309 Repair Rotating Assemblies
ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTYOM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 5
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 6PUMP AND SEAL DISASSEMBLYAND REASSEMBLYReview all SAFETY information in Section A.Follow the
OM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 7NOTEAn alternate method of removing the check valveassembly is to remove the hardware securin
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 8E‐3 for removal tool use). If the removal tool is notused, install three of the inner capscre
TABLE OF CONTENTSiINTRODUCTION PAGE I - 1...SAFETY - SECTION A PAGE A - 1...
OM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 9Shaft and Bearing Removal and Disassembly(Figure E‐2)When the pump is properly operated and m
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 10sparks, and flame. Read and follow allprecautions printed on solvent containers.Inspect the
OM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 11When installing the bearings onto theshaft, never press or hit against the outerrace, balls,
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 12SEAL PLATEO‐RINGSIMPELLERSHAFTSTATIONARYSEATSTATIONARYELEMENTROTATINGELEMENTDRIVE BANDBELLOW
OM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 13O‐RING ENGAGEDWITH SEAL PLATEBORESHEAR RING(UNSHEARED)Figure 7. Seal Partially InstalledCon
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 14Slide the rotating portion of the seal (consisting ofthe integral shaft sleeve, spring cente
OM-05291SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 15Suction Head And Wear Plate Installation(Figure E‐1)Clean any scale or debris from the conta
OM-05291 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 16Bearings(Figure E‐2)The bearing housing was fully lubricated whenshipped from the factory. C
For U.S. and International Warranty Information,Please Visit www.grpumps.com/warrantyor call:U.S.: 419-755-1280International: +1-419-755-1352For Canad
TABLE OF CONTENTS(continued)iiPUMP MAINTENANCE AND REPAIR - SECTION E PAGE E - 1...PERFORMANCE CURVE PAGE E - 1...
SUPER T SERIES OM-05291PAGE I - 1INTRODUCTIONINTRODUCTIONThank You for purchasing a Gorman‐Rupp pump.Read this manual carefully to learn how to safely
SUPER T SERIES OM-05291PAGE A - 1SAFETYSAFETY - SECTION AThis information applies to Super T Series basic pumps. Gorman‐Rupp has nocontrol over or pa
SUPER T SERIESOM-05291PAGE A - 2 SAFETYDo not attempt to disengage any part ofan overheated pump unit. Vapor pressure within the pump casing can eje
OM-05291SUPER T SERIESPAGE B - 1INSTALLATIONINSTALLATION - SECTION BReview all SAFETY information in Section A.Since pump installations are seldom ide
OM-05291 SUPER T SERIESPAGE B - 2 INSTALLATIONCheck that the pump shaft rotates counterclockwise when facing the impeller.Only operate this pump in
Kommentare zu diesen Handbüchern