DS OM‐05144‐01October 10, 2000Rev. L 03‐08‐13THE GORMAN‐RUPP COMPANY MANSFIELD, OHIOwww.grpumps.comGORMAN‐RUPP OF CANADA LIMITED ST. THOMAS, ONTA
OM-05144SUPER T SERIESPAGE B - 3INSTALLATIONcompatible with the liquid being pumped. If hose isused in suction lines, it must be the rigid‐wall, rein
OM-05144 SUPER T SERIESPAGE B - 4 INSTALLATIONIf it is necessary to position inflow close to the suction inlet, install a baffle between the inflow a
OM-05144SUPER T SERIESPAGE B - 5INSTALLATIONIf the application involves a high dischargehead, gradually close the dischargethrottling valve before sto
OM-05144 SUPER T SERIESPAGE B - 6 INSTALLATIONmoving the plug to prevent injury to personnel from hot liquid.AUTOMATIC AIR RELEASE VALVEWhen properly
OM-05144SUPER T SERIESPAGE B - 7INSTALLATIONALIGNMENTThe alignment of the pump and its power source iscritical for trouble‐free mechanical operation.
OM-05144 SUPER T SERIESPAGE B - 8 INSTALLATIONtems using two or more belts, make certain that thebelts are a matched set; unmatched sets will causeacc
SUPER T SERIESOM-05144OPERATION PAGE C - 1OPERATION - SECTION CReview all SAFETY information in Section A.Follow the instructions on all tags, labels
SUPER T SERIESOM-05144OPERATIONPAGE C - 2If rotation is incorrect on a three‐phase motor, havea qualified electrician interchange any two of thethree
SUPER T SERIESOM-05144OPERATION PAGE C - 3heated pump cautiously. It is recommended thatthe pressure relief valve assembly be replaced ateach overhaul
SUPER T SERIESOM-05144OPERATIONPAGE C - 4Temperatures up to 160F (71C) are considerednormal for bearings, and they can operate safely toat least 180
Register your newGorman‐Rupp pump online atwww.grpumps.comValid serial number and e‐mail address required.RECORD YOUR PUMP MODEL AND SERIAL NUMBERPlea
SUPER T SERIES OM-05144TROUBLESHOOTING PAGE D - 1TROUBLESHOOTING - SECTION DReview all SAFETY information in Section A.Before attempting to open or se
OM-05144SUPER T SERIESTROUBLESHOOTINGPAGE D - 2TROUBLE POSSIBLE CAUSE PROBABLE REMEDYPUMP REQUIRESTOO MUCH POWERPUMP CLOGSFREQUENTLYImpeller or other
SUPER T SERIES OM-05144TROUBLESHOOTING PAGE D - 3PREVENTIVE MAINTENANCESince pump applications are seldom identical, andpump wear is directly affected
OM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 1PUMP MAINTENANCE AND REPAIR - SECTION EMAINTENANCE AND REPAIR OF THE WEARING PARTS OF THE PUM
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 2SECTION DRAWINGPARTS PAGEFigure 1. Pump Model T6A3S-B, Including /F, /FM, /WW and /WWS
ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTYOM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 3
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 4SECTION DRAWINGASSEMBLED DRIVE END VIEWFigure 2. Repair Rotating Assemblies
ITEM NO.PART NAME PART NUMBERMAT'LCODEQTY ITEM NO.PART NAME PART NUMBERMAT'LCODEQTYOM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 5
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 6PUMP AND SEAL DISASSEMBLYAND REASSEMBLYReview all SAFETY information in Section A.Follow the
OM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 7NOTEAn alternate method of removing the back coverfrom the pump casing is to remove the back
TABLE OF CONTENTSiINTRODUCTION PAGE I - 1...SAFETY - SECTION A PAGE A - 1...
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 8TEEAPPROX. 6 IN.(152 MM) LONGAPPROX. 14 IN.(356 MM) LONGFigure 4. Rotating Assembly ToolTo i
OM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 9be cleaned and inspected in place. It isstrongly recommended that the bearingsbe replaced any
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 10hot plate may be used to heat the bearings. Bearings should never be heated with a direct f
OM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 11Inspect the seal components for wear, scoring,grooves, and other damage that might cause lea
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 12Lubricate the external stationary seat O‐ring withlight oil. Slide the seal assembly onto th
OM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 13cuts on either end. If any components are worn, orthe sleeve is damaged, replace the complet
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 14Reach through the back cover opening with thecheck valve and position the check valve adapto
OM-05144SUPER T SERIESMAINTENANCE & REPAIR PAGE E - 15Allow an installed pump to completely cool beforedraining liquid from the pump casing. Remov
OM-05144 SUPER T SERIESMAINTENANCE & REPAIRPAGE E - 16Power SourceConsult the literature supplied with the powersource, or contact your local powe
For U.S. and International Warranty Information,Please Visit www.grpumps.com/warrantyor call:U.S.: 419-755-1280International: +1-419-755-1352For Canad
TABLE OF CONTENTS(continued)iiTROUBLESHOOTING - SECTION D PAGE D - 1...PREVENTIVE MAINTENANCE PAGE D - 3...
SUPER T SERIES OM-05144PAGE I - 1INTRODUCTIONINTRODUCTIONThank You for purchasing a Gorman‐Rupp pump.Read this manual carefully to learn how to safely
SUPER T SERIES OM-05144PAGE A - 1SAFETYSAFETY - SECTION AThis information applies to Super T Series basic pumps. Gorman‐Rupp has nocontrol over or p
SUPER T SERIESOM-05144PAGE A - 2 SAFETYDo not operate the pump against aclosed discharge valve for long periodsof time. If operated against a closed d
OM-05144SUPER T SERIESPAGE B - 1INSTALLATIONINSTALLATION - SECTION BReview all SAFETY information in Section A.Since pump installations are seldom ide
OM-05144 SUPER T SERIESPAGE B - 2 INSTALLATIONPREINSTALLATION INSPECTIONThe pump assembly was inspected and tested before shipment from the factory.
Kommentare zu diesen Handbüchern